Meat Cutting Table Top
machine name
automatic frozen meat slicer machine
voltage
220v
power
350w
capacity
40kg/h
- Product Introduction
Commercial bone cutting machine

The operating instructions of the frozen meat cutter are as follows:
First, the user should clean the material to be mixed. If the material to be cut is mixed with sand and soil, the blade edge and blade are easily damaged and blunted. The maximum cutting diameter of the material should not exceed 100mm. If it is larger than this diameter, it must be divided into multiple blocks.
Then press the start button to run the motor. The material to be cut is fed from the hopper into the feed hopper evenly and continuously, and cut into the required thickness with the cutting knife under the action of the push disk, and then cut into strips with the disc cutter, and then cut into squares with the cutting knife.
Precautions for frozen meat slicer:
1. After each use of the chicken slicer, the machine must be cleaned, especially where the material passes and passes through.
2. Always carefully check whether the dicer cutting tool is damaged or blunt, and check whether the comb blade is normal or damaged.
3. Disassemble the disc cutting combination tool and cross-cutting combination tool once a week (be careful when disassembling, use professional tools to avoid injury) and clean them properly.
4. When reassembling the frozen meat slicer, non-toxic and odorless edible oil must be used for maintenance. Before installation, edible oil must be applied to the cutting shaft and cutting shaft to ensure easy disassembly. Fill the gears and chains every two weeks.

| machine name | automatic frozen meat slicer machine |
| voltage | 220v |
| power | 350w |
| capacity | 40kg/h |
| machine size | 660*380*700mm |
| machine weight | 65kg |
| adjustable thickness | 0.3-4.5mm |
| material | stainless steel |
butcher cutting machine
There are many issues to pay attention to before using the frozen meat slicer, and there are many precautions during operation. So what should we pay attention to?
In the process of putting the cut material into the dicer, we must see if there are any impurities on it. If there is some dirt or sandstone in it, it needs to be removed in time, otherwise it will easily cause the blade and the edge of the blade to become blunt or damaged. When adjusting the diameter of the cut, please note that the diameter of the cut cannot exceed one hundred millimeters.
If it exceeds this number, it is no longer a flat plate, but a block. When the frozen meat slicer is in working condition, handles or other objects cannot be placed in it, because it can easily cause dangerous accidents.

Before you start operating the automatic chopper, make sure the machine is clean. Check the sharpness of the knife and make sure it is properly installed. Also, check that the power supply and safety devices of the chopper are functioning properly.
Prepare the meat to be cut, which can be large steaks or frozen meat. Ensure the quality and freshness of the meat, which is crucial to the taste and quality of the final product.
Adjust the knives and parameters on the frozen meat chopper according to the desired cutting effect and type of meat. This may include adjustments to the cutting speed, knife angle, cutting thickness, etc. Flexibly adjust the settings of the chopper to achieve the ideal cutting effect according to different meats and processing requirements.

Our Advantages
150
+
Number Of Employees
3000㎡+
Factory Area
10
+
Years Of Experience
800㎡+
Company Area
Meat slicer cutting machine
The use of hardenable corrosion-resistant steel, namely martensitic stainless tool steel, ensures that the meat produced meets food standards, the blade is sharp, wear-resistant, has a long service life, good strength and toughness, no chips, continuous cutting, and no rust.
The wear resistance of the knife is related to hardness and good toughness. A good combination of hardness and toughness is the quality of the knife.
When sharpening the knife, a special sharpener should be used, and the whetstone should be cooled in time to prevent the knife body from overheating during sharpening.
After sharpening, clean the pressing surface and the tip of the knife. At least once a week, remove rust and apply animal fat. Clean and lubricate the shaft before installing the tool. It should be opposite and have the same structure, the same length as the heavy object, any imbalance will cause an increase in the load on the shredder, vibration, and even cause irregular operation of the machine, causing damage to the machine.
Qualification & Honor

Customer visits

Hot Tags: meat cutting table top, China meat cutting table top manufacturers, factory, meat cutting machine for stuffing events, meat cutting machine for mincing events, food service meat processing equipment, certified meat cutting machinery, meat processing equipment for sous vide with meat, meat processing machine for pastries with meat filling












