video

Fortified Rice Extruder

Model
DF50-28D DF62-28D DF72-28D
Capacity (kg/h)
60-100 200-350 350-500
power (kw)
37 90 110

  • Product Introduction

 

Snack extruder

 
corn snack extruder

How to install and debug the extruder?
Use square wood or channel steel to make a rectangular base according to the size of the extruder and motor foot holes, fix the extruder and motor on the base, hang the V-belt and tighten it.
Remove the nozzle before use, apply some cooking oil on the inner thread and screw head of the nozzle, tighten the nozzle again, tighten the front flange, and mix the rear flange evenly.
Prepare 2 taels of wet corn (soak for 5 minutes) before starting the extruder.
Turn on the extruder and let it run idle for half a minute. If there is no abnormal sound, put the wet corn into the machine one by one (be careful not to cut the material too fast at the beginning to avoid material reversal or action jam), spray, when the popcorn can be crushed by hand, it can be replaced with dry corn, and the amount of chopped can be gradually increased. Usually 20-30 kg of corn can be puffed per hour.

If the material is poured, it is because the material is cut too fast and the nozzle temperature is not 120 degrees. At this time, the material should be stopped. When the sprinkler sprays again, it will continue to run idle. If the nozzle still does not bloom after 5 minutes, the nozzle should be tightened again immediately, then the machine should be stopped, the screw rod should be removed to clean the remaining material, and the nozzle should be installed and used again.
If the flowers sprayed out are scorched because the temperature inside the machine is too high, a wet towel can be wrapped around the nozzle to cool it down.
If the flowers of the nozzle have a hard core, it is because the temperature inside the machine is low. The material should be stopped, and the material should be run idle for a while. The material can be fed again after the flowers are sprayed normally.

chips extruder
NO Model Capacity (kg/h) power (kw)
1 DF50-28D 60-100 37
2 DF62-28D 200-350 90
3 DF72-28D 350-500 110
4 DF90-28D 500-1000 160
5 DF120-20D 1500-3500 250
6 DF65-20D 250-450 37
7 DF78-28D 300-600 90
Food extrusion equipment
 

 

If there is a sudden power outage or other emergency shutdown during work, the nozzle should be twisted and removed immediately, and the jacket and screw should be burned in the fire until the remaining material is burned out. Then the screw and jacket can be separated, and be careful not to burn. The time is too long to avoid damage to the jacket and screw. If the nozzle cannot be removed, do not smash it hard. The nozzle and jacket can be removed together and boiled in the fire.
During normal shutdown, the extruder should stop feeding first, unscrew the nozzle, then stop, remove the screw, remove the remaining material, and apply cooking oil to avoid rust.

extruder in food industry
 

The twin-screw extruder has excellent raw material adaptability and can handle a variety of different types of raw materials such as high viscosity, low viscosity, high fat content, and high moisture. Compared with the single-screw extruder, the twin-screw extruder has higher stability and efficiency when processing complex raw materials, effectively avoiding the slippage of raw materials during processing.
The twin-screw extruder has less restriction on the particle size of raw materials and can process raw materials from micro powder to coarse powder particles. This gives manufacturers greater flexibility in raw material selection and reduces production costs. At the same time, the twin-screw extruder can also adjust the screw speed and barrel temperature according to production needs to meet the processing needs of raw materials of different particle sizes.

extruder snack
Our Advantages

 

150

+

Number Of Employees

3000㎡+

Factory Area

10

+

Years Of Experience

800㎡+

Company Area

 

Biscuit extruder machine

 

 

During the processing, the twin-screw extruder uses advanced screw design and optimized process parameters to evenly distribute the material in the barrel. This helps to ensure the uniformity of the quality of the product inside and outside and improve the overall quality of the product. In addition, the twin-screw extruder can also add auxiliary materials such as steam and water during the processing to achieve more precise material ratio control and better processing effect.
During the processing of the twin-screw extruder, the protein molecules in the raw materials are denatured through high temperature, high pressure and high shear force to form a compact and porous structure. This structure gives the product a good maturation and homogenization effect, and improves the nutritional value and taste of the product. Especially for starch raw materials, the twin-screw extruder can achieve a starch maturation degree of more than 95%, ensuring the stability of the product in water and the non-loss of nutrients.

 

Qualification & Honor

 

Qualification & Honor

 

Customer visits

 

Customer visits

 

 

 

 

Hot Tags: fortified rice extruder, China fortified rice extruder manufacturers, factory, food extruder machine distributor, food extruder for extruded organic products, food extruder for ready to eat bakery products production, food extruder for lasagna, food extruder for food waste reduction, advanced food extrusion machine

Send Inquiry

(0/10)

clearall